Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Fontana
Gate repair in Fontana usually costs between $185 and $520 depending on what’s actually wrong, and most calls are same-week, not same-month. We’re a gate-only shop, so when we roll into 92335 or 92336 we’re not looking at your gate as a side job. Call (833) 589-7839 for a free estimate and an honest read on whether repair or replacement makes more sense.
Fontana’s stock of 1950s-through-1980s tract homes means most of what we see here is older wrought-iron driveway gates and chain-link side gates hung off masonry pilasters that have been settling for decades. That’s a very different repair than a 2015 builder-grade ornamental setup on the north side. Being a Fontana-specific shop matters because the soil, the wind, and the age of the housing all shape what goes wrong, and what it takes to fix it right.
Why Ironcrest Gate Repair Is Fontana’s Preferred Gate Repair Company
Ironcrest works on gates, and only gates, and our Fontana customers notice. We’re not a garage door outfit that “also services gates,” and we’re not a handyman guessing at your operator board. Our entire practice is built around swing gates, slide gates, electric operators, hinges, tracks, and access control. That focus means when we arrive at a home near Sierra Avenue or a commercial property off Valley Boulevard, we’ve seen your specific failure before. Noel Ibarra runs the company around a simple premise: name the brand, know the failure mode, fix it without inventing work.
We cover all of Fontana, from the older blocks north of Foothill Boulevard in 92335 and 92336 down through 92337 and the newer subdivisions in 92334. Response time across the city typically runs one to three business days for non-emergency calls, and our dispatcher will give you a straight answer about when a tech can be there. We keep common parts on the truck for LiftMaster, FAAC, BFT, and Linear systems, so a lot of Fontana repairs happen on the first visit instead of after a parts run.
Styles & brands we work with
Wrought Iron Gate Repair in Fontana
Wrought iron gate repair in Fontana typically runs $225 to $480, and on the older 1960s tract homes we service throughout 92335, the job usually isn’t about the iron at all. It’s about the post the iron hangs from. In those blocks, the original block-wall driveway pilasters settle and tilt as the soil shifts through decades of hot dry summers and occasional winter rain. When a pilaster leans even a few degrees, the gate drags on the walkway, the latch misses the strike, and the homeowner calls thinking they need a new gate.
Hinge Post Re-Plumbing and Hardware Rebuild
We re-plumb the hinge post before we touch the panel. That means resetting the plate, shimming or re-anchoring the post to true, and rebuilding the hinge hardware under real load rather than adjusting the gate to match a post that’s still moving. Depending on how far the post has shifted, this runs $250 to $420 in Fontana and usually keeps the original gate in service for years.
Rust, Weld, and Latch Repair on Older Iron
Fontana’s dry climate keeps rust slower than coastal cities, but the winter rain still gets into older welds and hinge barrels. We grind, treat, and re-weld where the section has integrity, then re-hang the gate so it clears. If the iron is badly rust-jacked at the spine or bottom rail, we’ll tell you whether patching is cheaper than a new panel, with the number in writing before any work starts.
Metal Gate Repair in Fontana
Metal gate repair in Fontana covers both wrought iron and the lighter gauge steel, aluminum, and chain-link gates common across 92336 and 92337, and it typically runs $185 to $390. A lot of this work is realignment on gates that have been racked by the Cajon Pass wind corridor, which twists swinging panels seasonally. The fix on a wind-shifted gate is correcting the geometry at the post and hinge, not just cranking a lag bolt into a cracked stucco face and hoping it holds.
Sag Correction and Gate Realignment
When a metal gate drags or won’t latch, we find where the frame is out of plane. On the older side gates hung off stucco walls in Fontana’s working-class housing stock, that often means the wall side has pulled and the gate frame now leads with the top hinge. We correct the sag at the post or plate, re-set the hinge alignment, and adjust the panel so it hangs true under its own weight. The work is usually $200 to $380, and we re-test the latch throw before we call it done.
Latch, Strike, and Drop Rod Repairs
A gate that won’t stay closed is a security issue, and on a lot of Fontana side yards the latch is seized, the strike plate is wallowed out, or the drop rod no longer reaches the concrete after years of post settlement. We rebuild the latch mechanism, replace the strike with something that actually engages, and re-seat the drop rod so the gate locks like it’s supposed to.
Trusted Brands We Service in Fontana
We’re certified to work on nine major gate operator brands, and on a Fontana call that usually means a LiftMaster, FAAC, or BFT control board doing something it shouldn’t. Whether you’re running a LiftMaster on a residential driveway or a FAAC or BFT on a commercial entry off Valley Boulevard, our techs know the board, the limits, and the failure modes by sight. We stock common replacement parts locally, so a lot of Fontana electric gate repairs don’t wait on a distributor shipment out of Ontario or Riverside. Gate Repair is all we do, so we’re not learning your system’s manual in the driveway.
Common Gate Repair Problems We See in Fontana Homes
- Settled block-wall pilasters in 92335: The original 1960s driveway pilasters tilt with soil movement, so the gate drags or fails to latch. We correct the post before we touch the panel, because adjusting a gate to a moving post just means another call in a year.
- Wind-racked swing gates from the Cajon Pass corridor: Seasonal wind twists panels and works hinge hardware loose. Fontana gates need hinge bolts re-torqued and the swing geometry checked at least twice a year.
- Obsolete control boards on legacy operators: Older LiftMaster, FAAC, and BFT boards fail, and replacement parts are getting scarce. We’ll tell you honestly whether a retrofit or a new operator is the cheaper ten-year answer.
- Sun-baked stucco and cracked gate anchors: Intense summer sun cooks the stucco around hinge plates and post anchors, especially on west-facing side yards throughout 92336. Lags lose bite, the wall cracks, and the gate sags off its fixings.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Fontana, CA
Here’s what Fontana homeowners should expect to pay at the time of writing, with every price quoted and agreed before we start.
- Basic realignment or hinge re-torque: $185 – $260
- Latch and strike rebuild: $190 – $310
- Hinge post re-plumb or plate reset: $250 – $420
- Weld and rust repair on wrought iron: $225 – $480
- Control board or electric operator diagnosis: $160 – $340 plus parts
What moves the number is the post. If the pilaster has settled and needs re-plumbing, you’re at the higher end of the range. If the gate is sound and the hinges just worked loose in the wind, you’re at the lower end. Estimates in Fontana are free, and the price we quote is the price on the invoice.
We Also Serve Cities Near Fontana
If you’re across the border in Fontana, Bloomington, Rialto, Glen Avon, or Pedley, we cover those too. The housing stock and failure modes are similar enough that our Fontana experience carries straight over. Call (833) 589-7839 and we’ll get you on the schedule.
Serving Fontana, CA — Our Local Coverage Area
We’re based in the Fontana area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Fontana
In most cases it’s repairable. The gate itself is usually fine; the post it hangs from has tilted with decades of soil movement. We re-plumb the hinge post, rebuild the hinge hardware, and re-hang the gate so it swings clear. That fix runs roughly $250 to $420 in Fontana, and we’ll tell you before any work starts if the post is too far gone and a fresh footing is the honest answer. Call (833) 589-7839 for a free on-site look.
Fontana sits in the hot, windy Inland Empire corridor bordering Cajon Pass, and those sustained winds twist swinging gates and work hinge hardware loose seasonally. The original 1960s-80s tract homes also sit on soil that expands and contracts through dry heat and winter rain, so the posts move a little every year. We correct the misalignment at the post and re-torque the hinges, and we’ll show you which fasteners need checking before the next big wind event.
Yes, in most cases we can retrofit a modern control board to a working LiftMaster, FAAC, or BFT drive, including current UL 325 entrapment protection, safety edges, and photocells. The question is whether the motor and gearbox justify the board cost. If they’re tired, we’ll show you the math on retrofit versus replacement so you can decide with the numbers in front of you. Estimates are free at (833) 589-7839.
UL 325 is the current entrapment protection standard for automatic gate operators, and it requires working photocells or contact safety edges plus force-sensing stops on the motor in most installations. If your gate is original to a 1960s-80s Fontana home and has an operator added later, there’s a good chance it doesn’t fully comply. We test the safety circuit on every electric gate call and will flag any gap in writing.
Typically the problem is the hinge anchors pulling out of the sun-baked stucco or the gate frame itself bowed with wind load. We either re-anchor the hinges through to the structure with proper lags or re-set the gate on new hinges with the frame pulled back to true. On a Fontana side yard this runs $185 to $310 in most cases, and we quote the exact figure before we start.
Repair or Replace: Honest Advice for Fontana’s Older Gates
Fontana grew up as a steel-mill and rail town, and its housing stock shows it. The original gates on those 1950s-80s blocks, especially across 92335 and 92336, were hung before modern safety requirements existed, and a lot of them now carry legacy operators with obsolete control boards. When we walk a Fontana property, we’re not trying to sell a new gate. We’re looking at whether your existing post string is stable, whether your iron is structurally sound, and whether your operator can be retrofitted to meet current UL 325 entrapment protection while still being worth the money.
Here’s the honest version. If the hinge post has settled but the plate still has sound concrete behind it, we re-plumb it and keep your gate. If the post is cracked through, a fresh footing is cheaper than re-anchoring to a failing block. If the gate frame is rust-jacked at the bottom rail, patching buys years on a driveway gate but isn’t the right call on a high-cycle commercial entrance. And on operators: a quality retrofit board for a tired FAAC or BFT drive sometimes costs more than a new residential unit installed, which is why we put both numbers on the table before you commit to either. We’re gate specialists, not a sales floor. If it’s repairable, we’ll repair it, and we’ll tell you when replacement is the cheaper answer over the life of the gate.
We recently worked a 1960s tract home near Fontana’s old Kaiser Steel corridor in 92335, where the driveway swing gate dragged against a settled block-wall pilaster. Our tech re-plumbed the hinge post and rebuilt the hinge hardware, then corrected the sag at the post instead of the panel. A LiftMaster operator was re-mounted and the safety photocell was tested, and the gate now swings clear without dragging.
Whether you’re off Sierra Avenue in 92335, up in the newer subdivisions around 92336, or managing a commercial property in 92337, call (833) 589-7839 and we’ll give you a straight answer on what your gate needs and what it costs. Free estimate, written price, and the work done by people who work on gates every day.
Written by Noel Ibarra, Owner at Ironcrest Gate Repair, serving Fontana and the surrounding Inland Empire.